I’ve been hard at work behind the scenes recently. Enhancements include:
- Repeater dashboard (see sidebar link)
- Talkgroup ReWrite (see user guide)
- Slot 1 also supporting TG23510, rewritten to TG9 (see user guide)
- Purchased some RG214 to upgrade the radio <-> duplexer links, to minimise possible de-sense from stray RF.
- SMS service – repeater is able to send welcome messages, send you your current BER etc. (More on this soon, in the mean time, please see user guide).
I am also interested in getting some feedback on some points of discussion:
- Should FR go true multi-mode? Note, I don’t have radios for other modes at present, so this would require input from other stations to monitor the repeater in other modes, either by loan equipment or by users listening and reporting back to me if any issues are seen.
- GB7FR social meet – I’ve been meaning to do this for ages, probably at The Henty in Ferring. Are you interested?
Today I have upgraded the MMDVM firmware and host software to the latest version. Comments or reports appreciated.
Usage on FR has been pretty light, but that’s to be expected this time of year. I was away for almost three weeks and I guess others have been out enjoying the sun too.
I will, however, be monitoring Slot 1 TG9 over the next few days and also when possible next week, which will be an interesting test as I’ll be on the Isle of Wight.
Today I have added the MMDVMHost-Dashboard application to the reapeater. You can use this to see last-heard stations, current linked reflectors, your BER etc, all in real-time.
You can find it here:
I’ve been working on Access Control code for MMDVM and my current testing version is running on FR at the moment.
So, you should be able to use all the reflectors, echo, private calls, SMS, APRS gate etc, but only TG9 is supported on both slots from RF and from the network. If you transmit on a talk-group other than TG9 (or the other services mentioned above) then your transmission will not be repeated, either on RF or on the BrandMeister network.
Many of you have been using FR, which is great. All seems to be working well.
I was going to move then aerial today, but I find on looking that the anchor bolts I have bought need a 14mm drill bit and the largest I have is 10mm. I’m not sure if I’ll get the the shop on time today, so I think this job will be put off until tomorrow.
A couple of you have reported oddities where you were able to get in with low power and not it takes slightly more. I’m not sure that this is a problem, it might just be the trees growing or some other effect, but just to be safe, when I take the aerial down to move it, I will unscrew the fibreglass tube, check the connections and make sure it’s not taken on any water. These co-linear antennas are pretty simple, so there can’t be too much that can go wrong.
73 for now – Simon G7RZU
The TX and RX seem to have an auto power off timer set somewhere and had switched themselves off. The repeater is up now and I will look in to this today.
First switch on at 1224 UTC today. I need to nip out, so I’m going to jump in the car and try it out!
Today I have MMDVMHost installed and ready to go the the Pi. I have also flashed the newest MMDVM firmware to the Arduino.
I am meeting up with Andy on Friday to run the final setup and testing and then it’s back to my QTH to plug it all in. Not long now!
It is my pleasure to announce South Coast 9.
South Coast 9 (AKA Sierra Charlie 9 or SC-9) is a group linking TS1 TG9 on South Coast repeaters to provide wide-area coverage along the A27 corridor.
Current participants are:
- GB7BH (Brighton)
- GB7FR (Ferring)
- GB7PK (Portsmouth)
SC-9 is an rf access only network, so there is intentionally no corresponding reflector or provision for DMR dongle access.
SC-9 only has one rule; be considerate to your fellow operators. There is no specific etiquette or restrictions other than general good and considerate operating procedure. SC-9 is free from the “band police” and you are welcome to QSO as your normally would. SC-9 is not simply a calling channel. If you want to join in with an existing QSO or If you need to place a call, a simple “break” and polite request should be all that’s needed.